Parts and Prices for: Russco, QRK, Spotmaster, Broadcast Electronics, Micro-Trak, LPB, Sparta, Harris/Gates, Presto, Collins, ROK and Other Branded Idler-Drive Turntables
Updated 12/02/2013 0045 hrs. UTC
The parts list below is updated upon receiving parts from manufacturers after casting, turning or C&C'd work depending on specific need/ application. RTC has other parts in stock than those shown; we have chosen not to list these other parts until enough back-stock arrives so that we may supply you without having to say, "temporarily out of stock"! All parts shown are in-stock and ready for shipment. If you do not see an item you require, please inquire as to its availability. We may have two or three in-house not displayed or listed.Due to the age of these older analog turntables, many parts are no longer produced; which is to be expected after so many years. We will be stocking a number of parts for many different "idler-drive" turntables as well as some parts for older (1940's-1980's) belt drive units or combination idler/belt driven units. Some of our parts have to be ordered from our suppliers 90-120 days in advance, which may--in turn--cause a lengthy waiting time for our customers. We will strive to keep you informed, should there be an inordinate amount of time estimated that it will take for us to get your order to you. Many of our stocked-in-house, hard-to-find parts are salvaged from units we have chosen to disassemble in order to supply the needs of you, the collector/user. These may include frame skeletons, platters, platter wells (i.e., platters and platter shaft well matched set) and some electric motors. There are times RTC has on hand many disassembled units, all depending on the condition of the unit when we acquired it. The most costly part for RTC to acquire at a reasonable re-sellable price is the Bodine NYC-12 motor and a few other motors used by Russco as well as other idler drive builders. We will continue to add many types of specialty screws and fasteners toRTC'sline items in order to "dress-up" your deck or replace existing "worn-looking" fasteners. If there is a call for this part (whether 1 screw or 100), we will make every effort to obtain them for you. If you need something different to "set off" your table, emailparts (at) RusscoTurntables (dot com).
All prices are subject to change. Texas residents add 8% state sales tax.
Plateform Shock Mounts
All Plateform Shock Mounts are New Stock When upgrading, replacing all 3 (or more) motor isolation/vibration plateform mounts is strongly recommended. SNUBBING WASHERS are now in stock! All Plateform mounts will benefit greatly by adding a snubbing washer to the top and bottom of all plateform mounts (where space allows). They are designed to be used together with the correct plateform mount to help isolate and reduce vibration at each mount point.
ATTENTION QRK MODEL 12C OWNERS: depending on the model and year of manufacture, QRK used a slightly different combination of Plateform Shock Mounts. Instead of a PL100-A (1/2 lb.) at the back of the motor hanger plate, the 12C uses a 100PL-1 (1 lb.), with 2 100PL-2 (2 lbs.) mounts on either side of the motor. We have these, and a set of 3 (Part # 3-SET-QRK) is priced at just $32.40 [plus shipping]. *Note:depending on the motor mount screw holes placement, your QRK may require diamond-shaped mounts to the left and right of the motor. Contact us regarding your particular table's requirements.
See diagrams on Parts/Diagrams IIpage. We believe it is worth the small expense to add Snubbing Washers when you replace your mounts!
Description: "Square" (Aluminum Holder) Plateform Shock Mounts "New Stock" # 1 rating (1 required-Motor support) Max. Axial Rated Load @ 1/16in. (1.58mm) Deflection / 0.5 lbs. Axial Spring Rate for the 100PL-A=8 lbs/in. SINGLE Plateform Mount.
---------------------------------------------------------------------------------------------------------------------------------------------- "Square" (Aluminum Holder) Plateform Shock Mounts "New Stock" # 2 rating (2 required-Motor supports) Max. Axial Rated Load @ 1/16in. (1.58mm) Deflection / 2 lbs. Axial Spring Rate for the 100PL-2= 32 lbs/in. PAIR/SET Plateform Mounts.
*Sold as a set of 3.
Other Info: 1) Russco Cue-Master®, Russco Studio-Pro Model B® tables, also Sparta, Spotmaster, LPB and other "branded" idler-drive units.
2) * Some Russco owners have substituted part # 100PL-2 (2 lb plateform mount) in place of the original100PL-A. (1/2lb Plateform Mount) in order to retro-fit worn out or damaged motor mounts on the Studio-Pro and Cue-Master commercial turntables. Part 100PL-A in-house stock. The substituted part will work, BUT does NOT conform to original design specifications possibly increasing the noise and vibration characteristics from the Bodine or other Motor assemblies recommended by Russco. (Russ Friend & Associates)
The Axial Spring Rate for the 100PL-A = 8 lbs/in, the 100PL-2 = 32 lbs/in.
The Axial Spring rate difference (100PL-A vs. 100PL-2) is almost 3 times that of original design specifications. This difference can (and will) be applicable to heightened noise and increased transfer of vibration from the "semi-isolated" suspended motor deck. The cast Aluminum platter, (lathe-turned) is effectively part of the main deck skeleton making contact through both the oilite bearings within the shaft well assembly, the main "captured" bearings in the platter-shaft, the height adjustable bearing at the base of the shaft well and limited contact through the capstan head / idler wheel against the inside rim of the platter. Limiting transfer of noise/vibration within the unit is the basic job of the plateform mounts, if you change the design principles and weight load characteristics of the mounts the "harmonics" they were designed to reduce or nullify can increase dramatically.
*$36.95 Set of 3 9.59 for each additional mount
106PDL-2 # 2lb Plateform Shock Mounts
Aluminum "Diamond" Vibration / Shock Plateform Mount /2lb rating. Used on EARLY Studio-Pro, PRE Studio-Pro Model B. series as well as "Collins Amp" blower/fan mounts and some Harris Intertype Corporation "Harris/Gates" series of early turntables, *see below. (EARLY "Number/Letter designation= 106-PL-2)These (106PDL-2 Diamond) and the PN-106PDN "Square" Plateform mounts are interchangeable in most shock-mount areas. Both Series have equidistant cross plateform center-hole/center-hole measurement. In most Plateform mounting situations only two (2) attachment points are used, both cross-mount on it's longest axis (35.80mm / 1 13/32" ) even though the "Square" plateform mounts come drilled in 4 mounting points 25.77mm / 1 1/64" center-to-center square yet as stated, cross-mount drilled 35.80mm / 1 13/32".
Gates/Harris* "New” Stock / 2lb rating Part numbers 100PDL-A and 100PDN-2 (DIAMOND Plateform Mounts) are load specific as per original specifications for a number of Gates "Early" Turntables and can be substituted on some Collins 30S 1000 Watt Amps for there stock Blower/Fan. 1 @ $10.80 3 @ $31.95 4 @ $39.95 8 @ $76.99
100 PL-1 -1 (lb) Plateform Shock Mounts 1lb Harris / Gates CB500 and/or CB1200 in some cases. The Gates CB500 series used different configurations of plateform mounts depending on the year/series as the table evolved. There was up-to 8 Plateform mounts under-base, (4 on top the motor and 4 under). On other CB500 units there were 3 plateform mounts used; (see link, 3 mounts and motor bracket shown on mid-page) all mounts were set on a vertical axis spread equidistant around the motor.
Aluminum Holder, (NOT Steel holder 100 PDN-1, no longer in production), specified part by early Harris, Gates, Gates/Harris.
These mounts are Square (the first mounts were 100PDL-1 Diamond, steel) the 100 PL-1 will work nicely where original mounts were fitted. (Vertical axis at three equidistant mount points.) RTC does have Diamond Plateform mounts in steel, (see above 100PDN-2) These carry a higher static load rating of 2 lbs which can be used in place of the 100 PL-1 Aluminum mounts. The 100PDN-2 plateform mounts are a bit more firm but due in part to the size of the motor vs. weight and size of the platter along with total mass spun-up these can be interchanged without any problems. NOS factory recommended 100 PL-1 Static load 1 lbs, (.45kg) Normal axial natural Frequency. 18 (Hz) Static axial spring rate 33 lb/in, N/mm (5.7), Dimensions under NO load in.(") .30* (Set dimensions are measured and taken from height: i.e. (A) topside of METAL plateform mounting holder to top of mount where the "supported" member sits) (B) Dimensions under NO load from top of where supported member sits to under-side where rubber mount terminates and "snubber" washer sits .41. Same Dimensions under NO load mm as per same characteristics and measuring points above, (A) 7.6, (B) 10.4. Measurement from mounting points across to mounting point (center-to-center) 1.414 in, / 35.92 mm Plateform overall outside measurement, 1.25 in (31.7 mm) Neoprene rubber measurement (full circle diameter), 1.000 in, (25.40 mm) Mounting point for threaded bolt/nut width, .166 in, (4.22 mm) 1 @ $10.80 3 @ $31.95 4 @ $39.95 8 @ $76.99
We have in stock NEW NOS-type Idler Wheels for such major branded units as Russco, QRK*, Sparta*, some Collins (200 S series), LPB, Micro-Trak, some RCA 12-inch, and other idler-drive units that utilize the same wheel. *NOTE: Sparta and QRK 12-C series changed idler wheel diameter at a later date by almost 1/16", check your wheel for this variance in size! We also have--from time to time--a selection of used Idler Wheels that are in good shape, which we sell at a discounted price. We will not sell any used Idler Wheel that is worn or damaged in such a way that it would cause unsatisfactory performance when installed. Please email or call us for prices and availability of "gently used" idler wheels!
PLEASE NOTE: THE PAYPAL "BUY IT NOW" BUTTON BELOW IS FOR U.S. ORDERS ONLY!! FOR ORDERS FROM OUTSIDE THIS U.S.A., PLEASE EMAIL US DIRECTLY AT Parts (at) RusscoTurntables.com! This is because shipping rates vary for international orders. PLEASE--ONLY USE THE PAYPAL "BUY IT NOW" BUTTON IF YOU ARE ORDERING FROM INSIDE THE U.S.A.!Thank you!
U.S. Addresses Only: use our convenient BUY NOW buttons below for quick ordering of Idler Wheels for Russco Cue-Master or Studio-Pro Model B turntables!
PLEASE NOTE: a charge of $7.95 for shipping and handling will be added automatically at checkout when you use the Buy Now buttons. THIS SHIPPING/HANDLING CHARGE IS FOR SHIPPING WITHIN THE U.S.A. ONLY! There are additional charges for shipping outside the U.S.A.; PLEASE EMAIL OR CALL US DIRECTLY to place an order for international shipping, or for larger order amounts. Thank you!
There are times we have idlers for "other" tables in limited stock, email or ring-up RTC.
RTC PART #
MT-J-2049-1 Snubbing (Snubber) Washer. (See explanation above) $0.99 each/3 @ $2.97 *Out of stock
4TW - Idler Thrust-Washer, Teflon (2 Required--the larger one goes under the idler wheel, the smaller one on top, between the Oilite bearing and the retaining ring). NEW $1.09 each.
5ITR - Idler Retaining Rings. (Kit of two (2) different types supplied due to change-over within design of some units). NEW $1.09
6CR - Compression Spring for Shift Mechanism. (1 Required) Nos. $5.29*
7ES - Extension Spring for Shift Mechanism. (1 Required) Nos. $5.29* SAVE $1.63 by purchasing 6CR/7ES as a set (1-6R/1-7ES) $8.95
10SA - Shift Knob Arm, Threaded, 1/4 x 28 Plated or brushed Aluminum. Nos.* $8.99
11SK - Shift Knob, Aluminum Nos.* $8.99
MS-2 - Micro Switches (roller actuated switch; original replacement for Studio-Pro Model B speed indicator lights) $11.89 (set of 2)
SP-B - Shift Mechanism for Studio-Pro Model B. (Special Order) cast Aluminum NOS $59.95
SP-BU - Shift Mechanism for Studio-Pro Model B. (Used, excellent) $49.95
CM - Shift Mechanism for Cue-Master (Special Order) Cast Aluminum NOS Limited Supply $59.95
CM-U - Shift Mechanism for Cue-Master (Used/Excellent) Cast Aluminum $49.95
SP-IM - Idler Mechanism for Studio-Pro Model B. (holds Idler wheel) NOS -Limited supply $42.95 *Out of stock
SP-IMU - Idler Mechanism for Studio-Pro Model B. (holds Idler wheel) Used, excellent $32.95
CM-IM - Idler Mechanism for Cue-Master. (holds Idler wheel) limited Supply $42.95 *Out of stock
NOTE Idler wheel "carriers" are not interchangeable between Cue-Master/ Studio-Pro Model B.)
SS - NOS 3/8" x 6" Shift-Shaft Hard Steel, Tapered one-end for shift mechanism NOS Limited Original $16.99
S9SW NOS Limited Supply Switchcraft On/Off SPST, 3-1/2" total length. Requires 15/32" mounting hole Locking Type/Lever Original Equipment (SPST) SwitchCraft 120 Volt Nos.* $9.95 each.(RED "top" cap)
DSWT - Switchcraft NOS DPST leaf switch, normally open. 3-1/2" total length. Requires 15/32" mounting hole, 120V. Excellent substitute for SPST Switchcraft NOS "Leaf" Switch above. $9.95
SPB/CM-H - Motor Hanger (cast Aluminum) Motor support casting. Limited supply NOS Studio-Pro Model B / Cue-Master $49.95
14CAP - "Bathtub cap" Capacitor, For Switch "Click-Filter" AEROVOXC-CP53B1EF254V-630M-0.25MFD- 600VDC mounted under-deck (early) Military surplus NOS for on/off switch. (Switchcraft) $3.95 each.
15CAP - Voltage rating 400VDC Film Cap ("Click cap" for switch). Solder on legs of Switchcraft on/off switch used in later tables. $2.49 each.
8RPL-D - Red Pilot lamp (120 Volt Neon) Dome, Original equipment. NOS. $4.29 each.
8RPL-F - Red Pilot lamp (120 Volt Neon) Flat-top, Original equipment. NOS. $4.29 each
LO-17 - Bodine Electric Motor Oil. Original maintenance lubrication for Bodine and other motors. Use 2-3 drops every 3 months (more often if turntable is in operation for more than a few hours a day). 4-oz. bottle=$4.95
SIL - Bright Orange Weathers Omni-Glo NOS Speed Indicator Lamps (110 vac/60Hz) w/ 17"+ leads. Can also be used for Power Indicator Lamp. NOTE: these can be 'customized' with the 33 or 45 speed designations. $6.95 each, or buy a pair for $13.00 and save! *Please indicate when ordering if you want the 33/45 numbers added!
Partial update 6/2/10 1700 hrs (Z) Please see below for parts and some discriptions, more coming.
Click on main JPEG below to see more about each view.
Updated6/2/09 1700 hrs. (Z)
RTC highly recommends an outstanding re-building service for many idler drive wheels, ("pucks") through a company we trust without reservation! The company is Turntable Basics . Turntable Idler Wheel Rebuilding Services (the company who rebuilds the idler wheels) uses the original wheel "hub" and the bearing that came with the wheel. This company and its owner work technical wonders with wheels of all descriptions, conditions, makes and brands. Please see JPEG's of their excellent work near the bottom of the Other Idlers/Add-Ons page.
We use Turntable Basics for our Gates units as well as other units which can be very hard to find. Frankly, the cost to rebuild your idler wheel to ensure that your deck runs at the "right" speed is nominal, compared to having a motor re-built by a qualified re-builder at $200.00-$380.00! If you have a fine older unit that will not turn the platter smoothly, or the idler wheel has a "bump" or flat-spot, it's time to re-build the wheel! These days, cost and quality are paramount! If you want the job done right, check out their website and see their products or contact firstname.lastname@example.org personal attention.
Partial Update 7/18/2014 0250UTC Located in the U.S.A.
Email:parts (at) RusscoTurntables.com
RusscoTurntables.Com--a division of ValleyRidge Audio